1. 1

    Position paper in the portrait orientation.

  2. 2

    Fold the lower right corner across to the left side. When finished, the bottom edge of the paper should now be flush with the left edge.

    Advertisement

  3. 3

    Fold the excess paper down over the top of the triangle fold you just made.

  4. 4

    Open the last fold and trim the excess. You should now have a square piece of paper.

  5. 5

    Fold the crease on top of itself and then unfold. You should have a piece of paper with an "X" fold when finished.

  6. 6

    Flip the paper over, fold across the horizontal axis, and unfold.

  7. 7

    Fold the paper across the vertical axis and unfold. Note: Green guide lines are for reference in the next step.

  8. 8

    Bring the edges of the 4 diagonal folds together. This corresponds to the green guide lines in the image above.

  9. 9

    With the diagonal folds together, fold the two adjacent folds on each side onto each other to create a square.

  10. Advertisement

  1. 1

    Position the square from Part 1 so that the crease runs vertically and the open end is facing down.

  2. 2

    Fold the right side flap inwards.

  3. 3

    Repeat the last step for the left side.

  4. 4

    Fold the top triangle down on top of the last two folds.

  5. 5

    Unfold the last three folds.

  6. 6

    Carefully peel back the first layer of paper at the bottom and open it upwards.

  7. 7

    After opening upwards, fold the paper on the creases that were made in steps 2, 3, and 4.

  8. 8

    Crease the opposite side in the same way as the previous step.

  9. 9

    Flip the paper over and fold the right side flap inwards.

  10. 10

    Repeat with the left side flap.

  11. 11

    Fold the top flap downwards.

  12. 12

    Unfold the last three folds.

  13. 13

    Carefully peel back the first layer of paper at the bottom and open it upwards.

  14. 14

    Fold the left side inward over the creases.

  15. 15

    Repeat with the right side.

  16. 16

    Confirm that you now have a diamond-shaped paper with two free lower flaps.

  17. 17

    Fold the right section upwards behind itself diagonally.

  18. 18

    Repeat with the left section.

  19. 19

    Carefully unfold the crease in the right section and open the fold.

  20. 20

    With the fold open, fold the right section upwards into itself so that the section extends from the inside of the body.

  21. 21

    Repeat steps 12 and 13 with the left section

  22. 22

    Carefully pull the right section downwards to reduce the angle and re-crease.

  23. 23

    Fold the left section downward to create a head shape.

  24. 24

    Fold the left wing down and crease.

  25. 25

    Flip over and repeat with the right wing.

  26. Advertisement

  1. 1

    Pinch the breast area of the swan with your left hand and the middle portion of the tail with your right hand.

  2. 2

    Carefully pull diagonally towards the tip of the tail with your right hand. This should cause the wings to flap. Congratulations, you've just created a flapping swan!

  3. Advertisement

Add New Question

  • Question

    How do I make the other diagonal line/crease?

    Community Answer

    You can make the other diagonal crease by either folding the paper in half again to form a smaller triangle, or unfolding the paper and spinning it once. Then fold and do the same process you did the first time.

  • Question

    My bird's wings won't flap on mine!

    Community Answer

    You may have made a mistake in the folds. Undo the paper and try again or use a new piece of paper. Be sure to read the steps really carefully and to check against each image.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You'll Need

  • One 8.5 x 11 sheet of paper
  • Pair of scissors (optional)

About This Article

Thanks to all authors for creating a page that has been read 33,017 times.

Did this article help you?